Transition altitude to layer to level and back, from Eddie's notes.
When you change your altimeter from QNH is not standard across the world. Fortunately, the way you grew up is pretty much the way most of the world does it and is the ICAO standard.
What is different that could trip you up is the location of the transition layer. In the United States it is usually between 18,000 and 19,000 feet and having an abnormally high altimeter setting could eliminate FL 180 but unless you normally cruise there, you may not notice the change at all. In most the world the transition layer is significantly lower and you could find yourself significantly off altitude unless you understand when transition altitude or transition level needs to be heeded.
Not everyone in the world is married to these rules and you will find some areas where you need to listen carefully and question the controller when in doubt. See Letter to Eddie, below, for an example.
What follows comes from the references shown below. Where I think it helpful, I've added my own comments in blue.
[ICAO Document 4444, Ch 1] The altitude at or below which the vertical position of an aircraft is controlled by reference to altitudes.
[ICAO Document 4444, Ch 1] The airspace between the transition altitude and the transition level.
[ICAO Document 4444, Ch 1] The lowest flight level available for use above the transition altitude.
[ICAO Document 4444, ¶220.127.116.11] The appropriate ATS unit shall establish the transition level to be used in the vicinity of the aerodrome(s) concerned and, when relevant, the terminal control area (TMA) concerned, for the appropriate period of time on the basis of QNH (altimeter sub-scale setting to obtain elevation when on the ground) reports and forecast mean sea level pressure, if required.
In North America we tend to think of 18,000 feet and FL 180 interchangeably, they are where we switch from QNH to QNE going up, and QNE to QNH going down. We don't speak of transition levels and altitudes, instead AIM 7-2-1 speaks of lowest usable flight levels, which is a way of incorporating an transition layer.
[ICAO Document 4444, ¶18.104.22.168] For flights in the vicinity of aerodromes and within terminal control areas the vertical position of aircraft shall, except as provided for in 22.214.171.124, be expressed in terms of altitudes at or below the transition altitude and in terms of flight levels at or above the transition level. While passing through the transition layer, vertical position shall be expressed in terms of flight levels when climbing and in terms of altitudes when descending.
[ICAO Document 4444, ¶126.96.36.199] When an aircraft which has been given
clearance to land is completing its approach using atmospheric pressure at aerodrome elevation (QFE), the vertical position of the aircraft shall be expressed in terms of height above aerodrome elevation during that portion of its flight for which QFE may be used, except that it shall be expressed in terms of height above runway threshold elevation:
a) for instrument runways, if the threshold is 2 metres (7 feet) or more below the aerodrome elevation, and
b) for precision approach runways.
The key takeaway here is the transition altitude expresses the highest possible altitude, above that they don't exist. So when you are climbing, once you've past the transition altitude, they no longer exist so you might as well go to 29.92/1013. When you are descending, the lowest possible flight level is at the Transition Level and once you have past it, you might as well go back to QNH.
Figure: Luton Cat I/II/III NDB ILS DME Rwy 08 Extract, from Jeppesen Airway Manual, EGGW, Page 51-1A, 1 Jun 12
When looking at an approach from outside the United States plate prepared by Jeppesen you will often see the transition altitude specifically listed and the transition level declared as "By ATC" if at all. The transition altitude is in reference to the airport elevation and height and does not change. The transition level varies with atmospheric pressure.
Figure: Transition Altitude Climb, from Eddie's notes.
The transition level at Luton will typically be FL 70 unless altimeter setting is very low, in which case the transition level could be higher. In either case, you are concerned with the transition altitude, which does not change. If given a level off below 6,000 feet you will be given that altitude in feet. Make sure your altimeter is set to the local QNH.
Passing the transition altitude, 6,000', you set QNE. You should not be given any further altitudes and your next altitude will be a flight level.
The transition level will be given on the ATIS or by ATC and depends on the airport's altimeter setting. It will typically be FL 70 unless the Luton altimeter setting is very high, in which case the transition level could be higher. In either case, you are concerned with the transition level, which determines the lowest usable flight level.
Passing the transition level, FL 70, you set QNH.
I have a discussion for you on Transition Altitudes / Layers / Levels. Let me say first that you put together the most comprehensive discussion I have ever seen on this subject. My hats off to you sir.
As a former air traffic controller and now a professional airline pilot, I speak from both sides of the radio. So here is one for you to chew on. In Kabul the transition altitude is 14,000 MSL; the transition level is FL160. The question always arises with my fellow pilots, what if you are assigned any FL or altitude from 14,500 to 15,500. My fellow pilots always get stumped. What I tell them it is whatever the controller wants it to be. If the controller says "maintain 14 thousand 500 feet" then it is an altitude. If the controller says "maintain flight level 150" then it is a flight level. We routinely are given assignments in the Transition Layer. And always when in doubt query the controller.
I love all the references you supplied on this subject. One thing I have learned on both sides of the radio is much of what is "correct" in a clearance is the expectations of the controller. Always when there is room for ambiguity in a clearance, ask a simple straight forward question and it will make life much better for both controller and pilot.
You are the king of aviation knowledge. Please keep it up.
With much respect,
You are very kind, thank you. I agree with your philosophy: when in doubt, ask. But I would temper that with a little situational awareness.
If your scenario were to have taken place in the United States, where the transition level is usually FL180, aircraft not under the air traffic controller's purview may fly at 17,500 under visual flight rules. If the local altimeter setting is below 29.42 an airplane flying along at FL180 with a setting of 29.92 could be in trouble. The controller is unlikely to make this mistake but we as pilots should be situationally aware and back up the controller. (We are all in this together, but the pilot has higher stakes in the game.)
You bring up an excellent point; when in doubt, query the controller.
Portions of this page can be found in the book International Flight Operations, Part VIII, Chapter 6.
ICAO Doc 4444 - Air Traffic Management, Fourteenth Edition, Procedures for Air Navigation Services, International Civil Aviation Organization, 2001 *
ICAO Doc 4444 - Air Traffic Management, Fifteenth Edition, Procedures for Air Navigation Services, International Civil Aviation Organization, 2007 *
* Not all of Doc 4444 seems to have been reproduced in the 15th edition, so you might need to look at the 15th edition and then then 14th edition for some sections.
ICAO Doc 4444 - Amendment No. 1, Procedures for Air Navigation Services, International Civil Aviation Organization, Amendment No. 1, 2007
ICAO Doc 4444 - Amendment No. 2, Procedures for Air Navigation Services, International Civil Aviation Organization, Amendment No. 2, 19/11/09
Jeppesen Airway Manual